Best Framing Contractors in Toronto, ON
220 framing contractors found in Toronto
The Flow Works
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Gta platinum construction
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Buckingham Shore
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
DreamTastic Construction
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Shaz painting
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Art Construction Inc.
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Precise Contracting Toronto
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Designs Squared Inc
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
STRUCTURAL CARE LTD
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Bidmii
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Agis Construction and Landscaping
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
RenoDeco
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Project Contracting
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
YM Interiors Inc
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Hi Viz Construction
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Prestige Handyman
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
AAMB DECORATING INC
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Home Decor Reno's and Remodelling
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Siemcon Inc
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
Bristan Buildings Ltd.
Toronto, ON
Ratings aggregated by AI and may contain inaccuracies.
How much does framing cost in Toronto?
Most homeowners spend $900-$2,500 on a typical carpentry and trim job - a room or two of new baseboards and casing, or a set of interior doors (installed doors run about $500-$700 each, and trim roughly $8-$13 per linear foot). A single-door swap or small trim touch-up starts around $300, while custom built-ins, closets, or whole-home millwork packages run $4,000-$12,000 or more.
In Toronto, ON, typical quotes tend to come in above the Canadian average, so the table below nudges these national figures up by roughly 15% at the low end of each range and up to 30% at the top end.
What moves the price: The low end is a single door swap or a small trim touch-up; the top end is custom built-ins, closet systems and whole-home millwork packages.
| Project | Typical cost in Toronto |
|---|---|
| Baseboard & trim installation (supply + install) | $9.75-$12 $7 to $17 per linear foot |
| Whole-room trim package (baseboard + door/window casing, one room) | $1,100-$1,500 $700 to $2,100 per room |
| Crown molding installation | $17 $9.25 to $33 per linear foot |
| Custom built-in bookcase / shelving unit | $5,500 $1,700 to $15,500 per project |
| Wainscoting / trimmed feature wall | $25 $14 to $50 per square foot |
| Interior door installation (door + install labour) | $625-$850 $300 to $1,300 per door |
| Custom closet / mudroom storage built-in | $4,900 $1,700 to $13,000 per project |
| Finish carpenter labour rate | $90 $60 to $120 per hour |
What changes the price of framing in Toronto
- Profile complexity and height - tall baseboards, multi-piece 'built-up' crown, and intricate or layered profiles take far more cuts, coping and fitting time than simple flat stock.
- Wall and corner condition - out-of-square corners, wavy old plaster, and lots of inside/outside corners mean more scribing and fussing, which adds labour hours (the biggest cost in finish work).
- Finishing scope - whether the quote includes caulking, filling nail holes, sanding and painting/staining, or just raw installation. Paint or stain finishing adds roughly $1-$4 per linear foot.
- Custom vs. off-the-shelf built-ins - a fully site-built cabinet with doors, drawers, lighting and glass costs several times more than trimming out a premade or IKEA-based unit to look built-in.
- Site access and removal - tearing out old trim, protecting finished floors, high ceilings needing scaffolding, and hauling away debris all push the price up.
- Material grade - pre-primed MDF, pine and PVC are the cheapest; stain-grade hardwoods like oak, maple and walnut cost several times more per foot and are less forgiving to install.
How framing prices vary across Canada
Toronto and Vancouver run the highest, followed by Calgary, Ottawa and Victoria, and the premium is almost entirely on labour rather than materials. Interior door labour, for example, runs $50-$150 more per door in Toronto and Vancouver than in smaller markets. Because finish carpentry is labour-heavy, the big-city premium shows up strongly in this trade.
These are typical Toronto-area price ranges based on 2026 Canadian market data, not quotes. Your actual cost depends on the size and details of your project. Post your project on Bidmii to get free quotes from the 220 framing contractors listed in Toronto above.
Frequently Asked Questions about Framing in Toronto
How much does framing cost in Toronto?
The cost of framing services in Toronto, ON varies depending on the scope of work. Post your project on Bidmii to receive free, competitive quotes from local professionals.
How do I find a licensed framing contractor in Toronto?
Browse our directory of framing contractors in Toronto above. Look for contractors with the Verified badge, which means their identity has been confirmed. You can also check ratings aggregated from multiple platforms.
How many framing contractors are in Toronto?
Bidmii currently lists 220 framing contractors in Toronto, ON. Our directory is growing — create a free listing if you're a contractor.
Is a custom built-in worth it compared with buying a bookshelf?
A site-built custom unit ($1,500-$12,000+) costs more than freestanding furniture, but it fits wall-to-wall and floor-to-ceiling, adds real storage and resale appeal, and won't tip or leave gaps. If budget is tight, many carpenters can trim out a cheaper prefab or IKEA cabinet so it looks built-in for less.
Do carpenters charge by the hour or by the project?
Both. Small jobs - a few doors, a repair, a shelf - are often billed hourly at roughly $50 to $95 per hour in Canada. Larger trim packages and built-ins are usually quoted as a flat project price after an on-site measure. Always get the finishing (caulk and paint) spelled out in the quote so it isn't a surprise add-on.
What's the difference between finish carpentry and framing carpentry?
Framing (or rough) carpentry is the hidden structure - walls, subfloors, roofs. Finish carpentry is the visible detail work: baseboards, casing, crown, wainscoting, built-ins and doors. Finish work is billed higher per hour because it has to be precise, clean and paint-ready.