Best Masonry Contractors in Eden Mills, ON
1 masonry contractors found in Eden Mills
matt Moran company
Eden Mills, ON
Ratings aggregated by AI and may contain inaccuracies.
How much does masonry cost in Eden Mills?
Most Canadian homeowners pay $500-$1,500 for a typical masonry or brickwork repair - patching cracks, replacing spalled brick, a partial repointing, or a chimney repair (repointing runs about $15-$20 per square foot). Small few-joint patches start near $300, while bigger projects like full-house perimeter repointing ($5,000-$6,000), a chimney rebuild ($4,000-$8,000), or new brick or stone veneer run well past that.
In Eden Mills, ON, typical quotes often come in a little below the Canadian average, so the table below shades these national figures down by roughly 5-10%.
What moves the price: The low end is a small patch of a few joints or bricks; the top end is full-house repointing, a chimney rebuild, or new brick and stone veneer.
| Project | Typical cost in Eden Mills |
|---|---|
| Brick repointing / tuckpointing | $14-$19 $9 to $29 per sq ft |
| Full-house perimeter repointing (detached home) | $4,600-$5,500 $2,700 to $9,500 per project |
| Spalling / damaged brick replacement | $23-$60 $18 to $70 per brick |
| Chimney repair (crown, cap, minor to moderate) | $550-$1,400 $275 to $2,400 per project |
| Chimney rebuild (partial to full above roofline) | $3,700-$7,500 $1,400 to $14,500 per project |
| Brick veneer installation | $14-$22 $11 to $29 per sq ft |
| Stone veneer installation | $20-$32 $16 to $43 per sq ft |
| Small masonry repair (few joints, crack, or efflorescence) | $375-$825 $275 to $1,100 per project |
What changes the price of masonry in Eden Mills
- Height and access: upper-storey walls, chimneys above the roofline, and anything needing scaffolding or a lift cost far more than ground-level work.
- Job size vs. minimum charge: most masons have a roughly $1,500-$2,500 minimum, so small jobs cost much more per brick or per square foot than large ones, since setup, matching and site protection cost the same either way.
- Brick and mortar matching: colour-matching mortar and sourcing brick to match old or heritage brick adds labour and material cost; custom-matched work sits at the top of the range.
- Extent and depth of damage: surface repointing is inexpensive, but structural problems (bowing walls, failed lintels, deep spalling, or water damage behind the brick) push costs up sharply.
- Material type: natural stone costs more than brick, and full structural brickwork costs more than thin veneer.
- Heritage / historic homes: soft historic brick and lime mortar need specialist techniques and slower, more careful work, raising the hourly rate.
How masonry prices vary across Canada
Big cities cost more. Toronto and Vancouver run roughly 15-25% above the national average, driven by higher masonry labour rates, permits and parking, and demand for heritage-brick matching - Toronto's older brick housing stock pushes the top of the range in particular. Calgary, Ottawa and Montreal sit about 5-15% above average. Smaller cities and rural areas trend toward the low end.
These are typical Eden Mills-area price ranges based on 2026 Canadian market data, not quotes. Your actual cost depends on the size and details of your project. Post your project on Bidmii to get free quotes from the 1 masonry contractor listed in Eden Mills above.
Frequently Asked Questions about Masonry in Eden Mills
How much does masonry cost in Eden Mills?
The cost of masonry services in Eden Mills, ON varies depending on the scope of work. Post your project on Bidmii to receive free, competitive quotes from local professionals.
How do I find a licensed masonry contractor in Eden Mills?
Browse our directory of masonry contractors in Eden Mills above. Look for contractors with the Verified badge, which means their identity has been confirmed. You can also check ratings aggregated from multiple platforms.
How many masonry contractors are in Eden Mills?
Bidmii currently lists 1 masonry contractor in Eden Mills, ON. Our directory is growing — create a free listing if you're a contractor.
What's the difference between repointing and tuckpointing?
Repointing means grinding out crumbling mortar between bricks and replacing it. Tuckpointing is a finer, more decorative finish that uses two mortar shades to create crisp lines, so it usually costs a bit more. Both restore the joints and keep water out of the wall.
How often does brickwork need repointing?
Mortar typically lasts 25 to 50 years before it needs attention, while the brick itself can last 100 years or more. If you see crumbling, receding, or cracked mortar joints, or gaps you can slip a key into, it's time to have it looked at.
Why is the quote for a small brick repair so high?
Masonry has high fixed setup costs: matching mortar and brick, protecting the site, and often scaffolding. Fixing 5 bricks can cost almost as much as fixing 20, and most contractors carry a minimum charge of roughly $1,500 to $2,500 just to put a crew on the wall.